Sikafloor®-169

• Conformity with LEED v4 MRc 2 (Option 1): Building Product Disclosure and Optimization — Environmental Product Declarations
• Conformity with LEED v4 MRc 4 (Option 2): Building Product Disclosure and Optimization — Material Ingredients
• Conformity with LEED v4 EQc 2: Low-Emitting Materials
• IBU Environmental Product Declaration (EPD) available
• VOC emission certificate according to AgBB und DIBt approval requirements
• Class A+ according to French Regulation on VOC emissions

• CE Marking and Declaration of Performance to EN 13813:2002 — Screed material and floor screeds — Screed material
• CE Marking and Declaration of Performance to EN 1504-2:2004 — Products and systems for the repair and protection of concrete structures — Part 2: Surface protection systems for concrete — Coating
• Sliding test DIN 51130, Sikafloor®-169, Certificate No. 020109-15-11
• Sliding test DIN 51131, Sikafloor®-169, Roxeler, Certificates No. 020108-13-30a, 020108-13-31a, 020109-15-10a, 020109-15-13a, 020109-15-4a, 020171-14-1a, 020197-15-1a, 020197-15-5a
• Coating compatibility test PV 3.10.7, Sikafloor®-169, HQM, Report No. 14-04-14201871-7
• Biological Stress ISO 846, Sikafloor®-169, CSM Fraunhofer, Certificate No. SI/1008-533

Solvent free epoxy

24 months from date of production

The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.

Resistant to many chemicals. Contact Sika Technical Services for additional information.

IMPORTANT

No simultaneous mechanical and chemical strain

While the product is exposed to temperatures up to +60 °C, do not also subject it to chemical and/or mechanical strain, as it may cause damage to the product.

80 % r.h. max

Beware of condensation. The substrate and uncured applied floor material must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product. Low temperatures and high humidity conditions increase the probability of blooming.

< 4 % part by weight

Before overcoating the product, allow:

Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.

Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.

Note: These figures are theoretical and do not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.

MIXING EQUIPMENT

• Electric single paddle mixer (300 to 400 rpm)
• Electric double paddle mixer (> 700 W, 300 to 400 rpm)
• Forced action mixer

MIXING PROCEDURE

1. Mix Part A (resin) for ~10 seconds with a single paddle mixer (300–400 rpm).
2. Add Part B (hardener) to Part A.
3. Switch to an electric double paddle mixer (300–400rpm, > 700 W).
4. While mixing Parts A + B, gradually add the required filler or aggregates.
5. Mix for a further 2 minutes until a uniform mix is achieved.
6. To ensure thorough mixing, pour materials into another container and mix again to achieve a smooth and uniform mix.
7. During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.

IMPORTANT

Protect from moisture

After application, protect the Product from damp, condensation and direct water contact for at least 24 hours.

IMPORTANT

Temporary heating

If temporary heating is required, do not use gas, oil, paraffin or other fossil fuel heaters. These produce largequantities of both carbon dioxide and water vapour, which may adversely affect the finish. For heating, use only electric powered warm air blower systems.

BINDER

1. Pour the Product onto the surface.
2. Apply the Product evenly over the surface with atrowel.

SEAL COAT

1. Pour the mixed Product onto the surface. Note: The consumption is specified in Application Information.
2. Apply the Product evenly over the surface with a squeegee.
3. Back roll the surface in two directions at right angles with a short pile roller. Note: A seamless finish can be achieved if a "wet"edge is maintained during application.

Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened material can only be removed mechanically